Certified technicians · Same-day service · 24/7 across Sharjah, with genuine parts and up to 90 days warranty.
Fully automatic washing machines do it all from a single button — fill, wash, rinse, drain and spin — which is wonderful until something in that sequence goes wrong and the whole cycle stops. Because they rely on electronic controls, sensors and valves working together, a fully automatic machine can fail in more ways than a simple one, and an accurate diagnosis is essential. Al Tareeq Home Appliance Repair Services provides expert fully automatic washing machine repair across Sharjah — both top-load and front-load — with certified technicians who find the real fault and fix it the same day, with genuine parts and a warranty.
From our workshop in Muwaileh Commercial we reach every area quickly, carrying the parts most repairs need. Whatever the brand and whatever the error, we get your fully automatic machine back to reliable, one-touch washing with an honest, upfront price.
A fully automatic machine runs its whole cycle under the control of an electronic board that reads sensors — for water level, temperature, door lock and drum speed — and switches valves, the heater, the motor and the pump at the right moments. That sophistication is exactly why a fault can be harder to pin down: a machine that “won’t spin” might have a drainage sensor issue, a door-lock fault, a motor problem or a control-board glitch. Rather than swap parts and hope, our technicians read the error code, test the sensors and components in sequence, and identify the true cause — which saves you money and gets the repair right first time.
One of the advantages of a fully automatic machine is that it usually tells you something is wrong with an error code — and that code is a valuable clue. Different codes point to drainage problems, water-inlet faults, door-lock issues, heating faults, or motor and sensor errors. If your machine is flashing a code, note it down before you call; it helps our technician arrive prepared and diagnose faster. We interpret the code, confirm it with testing, and fix the underlying fault rather than simply resetting it, so the same error does not return next wash.
Simple and transparent, from the first call to the final test:
Most complaints trace to familiar causes. Won’t fill usually means a faulty water-inlet valve or a pressure-sensor fault. Won’t drain or spin is often a blocked pump or filter, a door-lock fault, or a drainage sensor issue. Stops mid-cycle can be a heater, motor or control-board fault. No power or no response points to the control board or supply. We work through these logically, using the machine’s own error reporting, so the repair addresses the real problem.
The price depends on the fault. Clearing a blockage, fitting an inlet valve, a door lock or a drain pump is quick and affordable; a heater or sensor is a modest job; a control board (PCB) is a larger repair. The brand and part availability also matter. We always diagnose first and quote upfront, so you know the price before we start and only pay for what is genuinely needed. Because fully automatic machines are a worthwhile investment, most repairs make good sense against replacing the machine.
A little care keeps a fully automatic machine reliable. Use the correct detergent and dose for automatic machines and hard water, as excess suds confuse the sensors and strain the pump. Clean the drain pump filter every month or two, check pockets so nothing blocks the drainage the cycle depends on, and avoid overloading, which stresses the motor and bearings. Run an occasional maintenance or drum-clean wash, and leave the door ajar after use on front-loaders to prevent mould. These habits keep the electronics and mechanics working smoothly.
Every job is quoted upfront after a quick diagnosis. As a guide:
| Service | Cost Guide |
|---|---|
| Diagnosis & error-code check | Free with any repair |
| Water inlet valve / drainage fix | On request |
| Door lock / pump replacement | Quoted before work |
| Heater / sensor replacement | Quoted before work |
| Control board (PCB) repair | Quoted after diagnosis |
You always know the price before we begin, and the call-out charge is adjusted against the repair when you proceed — so you only pay for approved work.
We repair fully automatic front-load and top-load washing machines from every major brand sold in the UAE — Samsung, LG, Bosch, Siemens, Whirlpool, Hitachi, Daewoo, Candy, Super General and more — using genuine or OEM-grade parts.
We reach every area fast, from Al Nahda, Al Majaz and Al Qasimia to Muwaileh, University City and beyond.
My fully automatic machine shows an error code — can you fix it?
Yes. The code is a useful clue — note it if you can. We interpret it, confirm the fault with testing, and fix the real cause so it doesn’t just reappear.
The machine stops part-way through the wash — why?
Common causes are a drainage problem, a door-lock fault, a heater issue or a control-board glitch. We diagnose which and repair it.
Won’t fill with water — what’s wrong?
Usually a faulty water-inlet valve or a pressure sensor. Both are repairable, and we test to confirm before quoting.
Do you repair the control board (PCB)?
Yes — we repair or replace control boards and sensors, and always check simpler causes first.
Do you repair both front and top load automatics?
Yes — fully automatic front-load and top-load machines of every major brand.
My machine won’t start at all — is that fixable?
Usually yes. A machine that’s dead or unresponsive often has a power-supply, door-lock or control-board fault, all of which we diagnose and repair — we check the simple causes before the board.
Can you come the same day?
Yes, in most cases, often within the hour, with common parts carried for a first-visit fix.
Which brands do you repair?
All the major ones — Samsung, LG, Bosch, Siemens, Whirlpool and more — using genuine or OEM-grade parts.
Can a control board (PCB) be repaired, or does it need replacing?
Sometimes it can be repaired at component level; other times replacement is more reliable. We diagnose the board properly and recommend the most cost-effective option honestly.
My machine resets the error but it comes back — why?
Resetting clears the code but not the underlying fault, so it returns. We fix the actual cause — a sensor, valve, pump or board — so the error stays gone.
Is a fully automatic machine worth repairing?
Usually yes — these are a significant investment and most faults are economical to repair. We’ll advise if an older machine is genuinely beyond it.
Is the repair guaranteed?
Yes — up to 90 days written warranty on parts and labour, with a return visit if a covered fault comes back.
Get your machine back to one-touch washing. Call Al Tareeq Home Appliance Repair Services on +971 52 148 6431, or message us on WhatsApp, for expert fully automatic washing machine repair across Sharjah — same day, fairly priced and backed by warranty.
Our certified technicians are on standby 24/7 across Sharjah — same-day service, honest upfront pricing, warranty-backed.